Spektrum iX12 Start Up Issue

 

My Spektrum iX12 has been more or less stress free and operating well, even through updates that raised issues for so many other users. Well, I had left my radio "off" for several weeks, and when I went to turn it on, it would not boot. Plugged it in, booted fine, and checked the battery, it was red line low. I charged it overnight, and it took its charge fine, as expected. But my iX12 has a new trick. It will no longer boot Android if it has been turned off. I have to unplug the battery, plug it back in, and then it will boot. Curiously, it will also boot every time if plugged in. I tried the original battery, same issues, so its not the battery. No one seems to know why this happened. It started before the last update. I thought maybe its an Android OS issue, but there is no way that I can see to repair or update the Android system, and to my knowledge it has never been updated. It is set to automatically update. I am using the latest Airware.

I didn't want to damage the battery plug in the radio, so I installed a switch I happen to have. It fits nicely in the battery bay, and isn't tall enough to block the cover. It works perfectly.

A simple Radio Shack On-Off switch. I had a couple of these sitting around unused.  Soldered it in-line, then covered it in shrink wrap.

Here it is in situ. The wires on the MaxxPack are long, allowing this. Took 5 minutes.

Here's hoping this problem gets solved, or I figure out a new way. I may buy another MaxxPack just to see if it somehow turns out to be a battery thing after all.

I would rather have a Spektrum NX10 radio.

Waco 26cc is ready to fly!

Yes! I have completed the repairs on the Waco and programmed it into the iX12 transmitter! Tomorrow I plan to get the engine running, and if time permits, get her to the club field to fly. The conditions look great.

I have admitted the complex curves with cote are not my strong point. Here I am halfway completed on the starboard side wing root, using a cote iron, and some heat gun.

It looks pretty darn good. Close up its not perfect, but that'll do.

Tank reinstalled, installed the battery tray (velcro).

Tank is offset a bit for the battery.

Aileron leads out, battery in, cozied up.

Flight ready!

In programming it I worked on the Eagle A3 stabilization system. Why does she have one? I don't know, just felt like it since the original had the doomed Spektrum Alpha6 system. Replaced that with an Orange Stabilized System, and replaced that with this A3. The gain pots are hard to adjust. I turn them up, to set the directions of the surfaces, and turn them down as low as I can, but they still seem a bit aggressive. I'll be careful. The pot screws don't move negative well. I have it set up on Flight Mode switch. 

Tomorrow, we fly!

Waco Repairs Day 3

I made a lot of progress yesterday on the Waco repairs. While my work is not always elegant, and I really have no idea how to lay down large areas of cote with complex curves, I did a pretty decent job on this project!

The port side of the fuse had one minor cote cut out where I made a small sheet repair.

You can see the reconstructed wing root surface here, painted red. I didn't feel like cote-ing over.

Managed to match the curve nicely.

This is the starboard side. this required massive puzzle reconstruction because my skill set does not include forming balsa sheet into complex curves. Its not fully apparent here but there is a continuous S curve along the side through the wing root. The patch work came out smooth and follows the contours nicely. Spackle smoothed the remaining cracks and crevices. Allowing this to set overnight before a light sanding and ironing on the cote.

As I feared, I didn't manage to align the port wing root hardpoint and its wing tab. This happened because of a curious "oversight". See that piece of vertical wood with the hold in it on the left of the hardpoint and screw? So that fit perfectly, both on the tab side, and almost on the bulkhead (you can see it duplicates part of the wood its attached to). That hole in the wood also clearly has red on it from the cardboard wing tube guide; that indicates it should be in FRONT of the tab, not behind. This assembly of the hardpoint and this piece of wood fit so nearly perfectly in the spot I decided to go with it hoping the alignment would be spot on as a result. Later I would realize that this piece of wood was certainly on the WRONG SIDE OF THE AIRCRAFT. Nothing survived of the starboard side internal attachment of the hardpoint so I couldn't match fit it, but the clues were obvious I had repaired this wrong. So, no surprise the hardpoint and the wing root tab did not align. I popped out that piece of wood with the hole in it and discarded it, and with less difficulty than I expected, extricated the hardpoint, aligned it properly and reinstalled it.

Perfect. The port wing attachment hardpoint after realignment repair. Put a cross piece between the hardpoints spanning the fuse, will strengthen this with the goal of distributing any forces across both hardpoints. It does not touch the stringers underneath.

The underside, sanded and sealed with thinned epoxy (like fuel proofing). 

Wanted to seal the spackle from moisture. The lower (port) side is the side that externally took severe sheet damage that required extensive puzzle piece repair. It came out awesome. You can see the complex curves.

As admitted, my large complex curve cote skills are lacking, but this came out decent. I applied 3 layers of cote to strengthen the underside, having decided not to fiberglass it.

The underside is also done!!!

This whole repair project is going much better than I had ever imagined. Not wanting to deal with the complexity of the repair, and worried it was trashed inside, I had set it aside all fall, winter and spring. I am pleased this has gone so well, can't wait to finish up that starboard side, put the wings on, start her up and FLY!

Waco Repairs Continue Day 2

The wing tube was really just a pair of cardboard guides. All of the wing lift forces were transferred to the fuse only at the two wing mounting lock tabs, secured with one screw on each side used to mount and dismount the wings. Any yaw torque on the wings was transfered to the thin balsa sheeting and stringers, not capable of withstanding that. So when the weeds yawed the wings they tore the sheeting and stringers and the serious damage resulted from a light force applied just wrong. I am replacing them with a carbon fiber tube that traverses the fuse and is firmly secured in all planes. Its not going anywhere.

Ugly patch work. Replanted the formed pieces that had been attached to the cote that laid over it when it was fractured. Lots of epoxy on curved surfaces will be very hard to sand.

As discussed above, the wing mount hardpoint was more firmly attached to the port side, ripping out the entire underside it was attached to. The Starboard side mount popped without taking the fuselage sheeting with it..

I am not entirely confident that the wing mount hardpoints are properly placed and aligned, but that sucker is firmly epoxied now. I would go on to strengthen the surrounding structures for more support. 

Here you can see the carbon fiber wing spar tube being measured in place. It was nicely perpendicular to the midline. I am sure its aligned properly.

Now installed. You can see the tube is perfectly aligned with the frame. Note that the port (lower) wing hardpoint is against the tube, but the starboard one (top) has a couple of mm of space. I am not confident these are aligned. They are placed where the nearby attached parts made them fit. They may not have been aligned before but worked.

To act as a hardpoint for the wing tube I installed a dowel in front of the wing tube, epoxied in full contact with the wing tube and a frame abutting the bottom tray. The wing tube is going to affect fuel tank fit, but we will deal with that later. This firmly transfers forces to the major fuselage structures rather than  just a few stringers and sheeting.

That heavily epoxied ares sanded as best as I could.

Spackled, done for the day to allow all the sparkling a good 24 hr dry before hand sanding smooth.

This repaired area underside was more patch worked than the side was. Thought I had a pic, but alas here it is spackled. After sanding I plan to apply a thinned coat of epoxy, and then will put a Sheet of cote across the stringers there. I am considering laying down a sheet or two of fine fiberglass onto provide a lot of structural strength. I think that may be needless, and add more weight than benefit.

So tomorrow will be telling. I will test fit the wings and see if I will need to come up with a new way to secure them to the fuse if the hard points don't allow an aligned fit. The space difference between the tube, which is true,and the mounting hardpoints suggests this isn't going to go well.

 
 

Waking up the Waco

I learned last year that the Phoenix Waco wing connection to the fuselage was poorly designed. I ran it into some weeds and it tore the wings off. Weeds. The damage was massive, so disheartening I let it just sit on the floor broken for the entire fall, winter and spring. Today I decided to take up the challenge. This plane is a sweet flier and one of my favorites. It deserves a rebirth.

She spent three seasons sitting here.

And so, the work begins. The following assess the damage.

Epoxy everywhere. The hard point (the bolt) was torn out on both sides. This was the only hard connection point, a screw pressing down on a flange from the wing.

The patient had to be secured to the table to allow access to the less damaged starboard side. I needed it fixed first to help align the cardboard tubes used to guide the aluminum wing spar. I think I want to replace the two small cardboard tubes with a full span carbon fiber tube. I think I have one that can act as a supporting guide for the aluminum tube.

I like to overbuild the repair. The hard point is now epoxied in much stronger than the original which was secured with hot glue. Runners are stinger and doubled (popsicle wood). Letting things dry.  More to follow!

 

FINALLY! Awesome flying day!

Today was that perfect golf swing kinda day! That one where you getting kinda frustrated, depressed even, and then you hit that sweet spot with a graceful fluid swing and the ball sails. It was that kinda day!

Yesterday was disappointing. The PulseXTs RCGF-USA 26cc was still misbehaving, and the once perfectly fine RCGF-USA 35cc decided it wouldn't start. Today I decided to see if the M4F sparky was the same as a CM4, it fit in the 35cc, and it ran sweet right away, so yes! I couldn't find M4Fs anywhere, so this was great! Have 3 CM4s. Since this worked, I decided to replace the M4F in the 26cc as well, and damned if that wasn't the cure! I thought I had changed it last year, but it being the unfindable M4F that wasn't possible. That was easy. She too now runs pretty smooth!

Beautiful day to fly! Solid steady cross wind, but easily handled.

PulseXT 60 with its now sweet RCGF-USA 26cc!

Sweet once again!!

Straight out 90 degree wind! At least it was consistent

The innards of the MX-Bach. So glad she is running wonderfully, and flying well. She is super sensitive to control inputs. Dropped the DRs and found the expos a bit much making her a bit sluggish (55% on the ailerons, 80% on the elevator). I dropped the DRs, and next time will change the expos (forgot to give that a try today). I had to dial in a minuscule amount of up elevator on the flaperons. These humongus control surfaces have such profound effect. The full down flaperons need me to max the DR for any control authority, so I need to decrease the throw of the flaps to give it some more authority and less drag. The winds were getting gusty up high and she spooked me a couple of times, so I landed and called it a day. Every takeoff was smooth, every landing greased.  I love the way these heavy planes land. Awesome day.

New spark plug, all is well!

Next, I think I need to fix the Waco! Ground looped it into the weeds and that torqued the wing. I think it won't be as bad I as fear.

So great to have an awesome flying day, that perfect swing kinda day!

Welll, that's just annoying is what that is...

The RCGF-USA 35cc was running just fine. Got her to the field and she would not start... After a hundred flips and occassional sputters, I did get her running, but when I went to idle she quit suddenly, no wind down, just quit. Got her to do that twice in 90 mins before I gave up. I have no idea what its problem is, and really don't feel like taking the engine apart, but a boy gotta do what a boy gotta do I guess.  I am hoping she will just start tomorrow and we agree to forget these shenanigans.

I was soooo excited to fly her, but alas... unrequited.

I did fly the PulseXT 60 with the 26cc, but she started sputtering again, mostly at WOT. It is what it is, there is nothing more I can do for it now. I accept it. This plane is such an amazing flier.