Volts (Pressure), Amps (Gas), and Resistence (Loads)

Volts is the pressure in the tank, Amps is the actual gas (also volume), and Ohm (resistance) is loads, including the diameter and length of the "tubing" (wire), and resisters along the way (loads, like lights, motors, radios, etc).

Ohm's Law.   Voltage = Amps x Resistence (V = I x R)

FFF Workwear Workshop Apron

For Christmas my wife bought this lovely shop apron from a company a friend of hers owns, FFFWorkwear. I LOVE THIS APRON!  Fit, Form and Function, as promised. I like the X-back straps so nothing hangs off my neck during the hours I spend gnashing my teeth, I mean, enjoying fixing airplanes and helicopters I crash. Plenty of pockets for me to forget where I put a tool only to find it right where I left it, and sturdy enough not to let me get burned, melted or burst into flames when I run into my coting iron or Dremel Tool.  It is built to work and take a beating. Best apron ever!

They are also on Facebook!

Highly recommended!

Taking Batteries Down to Storage Voltage

Every so often I will have batteries I haven't flown and need to put them in storage voltage using the Storage protocol on my 208B charger.  You really don't want to leave charged batteries for more than a few days as this causes chemical changes that increase the internal resistance, which decreases their function. (It's important to check the internal resistance using your multi program charger from time to time. A battery is best around 10 micro ohms per cell, above 20 it's time to get rid of it). If I have the time I use a parallel setup to take up to six unused batteries down to storage, but it takes a lot of time. It's faster to discharge them by running them down to around 3.87V per cell off load. I attach them to the voltmeter (battery checker) while doing this.  On load they look lower, so I stop every so often and see what the voltmeter reads. On my 500 heli without the resistance of the blades it can take 10-15 minutes, where in flight I get 5-7 min depending in the mAh of the battery. I use a plane if I have one that fits the battery. If I can be outside I just practice hovering. If I am indoors I will take main and tail blades off for safety, or just secure a plane.

Blue canopy kinda day.

Disposing of Lipos

A couple of pointers on how I dispose of batteries, since zinc had several I haven't used in years whose IRs had surpassed the limit of 20 mohms per cell. I first discharge them down to at least storage, 3.8V per cell. I like to save the wire leads as then may come in handy, I also like to safe them from shorting, so I cut them.

Cut each lead ONE AT A TIME or the short will make you piss yourself.  Or so I have been told, I, um, wouldn't know.

Wind electrical tape first around one, then both.

The balance leads carry a charge and will also short if you don't also cut them one at a time. I cut them each slightly longer than the next reducing the chance of a contact short.

I keep them spread put on tape, then fold the tape without bunching them.

Close them all up.

NEVER THROW THEM IN THE TRASH! Compression in the truck can cause an explosion injuring the garbage guys, and can set their truck on fire. Best to take them to Lowes or Home Depot, and drop them in their LIPO  disposal box. If your recycle center takes them, you can take them there, of course.

iX12 Throttle Mixing Question...

My Pulse XT60 26cc gasser that has a tad high idle, and gets variably unstable if we try to end point it down. Gary Hoffman, a Horizon Hobby Rep and poweruser (iX20) noted he has a THR<THR mix set on Swith A that when he flips it on final it decreases his throttle 5%. His plane, like mine, will tolerate that at idle, for a minute or so. This allows a slower touchdown. If he needs power, it's there, just 5% less, until he returns the switch to flight position.

We looked at my iX12 and were able to assign a THR<THR to Switch A in Mix1, but nothing we set on either of the available end points (or TRIM, for that matter), resulted in a drop in RPM.

Any ideas?

Field Trip: RC Aces, North Hampton, NH

Went out to RC Aces field in North Hampton, NH, home field for my flying friend, Gary Hoffman. This would be my first real flights (I don't count thr UMX Debacle) on the iX12.  I was going put to SNHRCC at Hudson, but when Gary told me he was going out, I invited myself.

Baby's First Trip in her carrier!

The Stik flew well! The RCGF 10cc ran fine, lots of power. The twitch in the left aileron came back. In flight she did an un-commanded aileron roll at about 720 degrees a second! Snap, over as quick as it started, level to level. That quickly ended that flight. Inspection revealed that with the engine running the LA twitch was back, subtle. 

The very old AR610 that was in there died during preflight before I left, but I had the new antenna-less AR620, still in it's box. Like all of us, I was a bit worried about how this would behave, but I have faith in Spektrum. At the field we range tested it, and as hard as I tried, never more than -70 db loss, no holds, and in flight only 1 fade. Love the telemetry on the iX12! The snap roll was not a radio issue. The new radio and new reciever worked fine!

Is this gap in the webbing the cause of the twitch?? The wire covering is gapped and frayed,  not just here, so the ignition does need to be replaced. Ordering one tonight from RCGF-USA. I checked the servo and wires, and they are fine. Hope this is it.

I had set up the Pulse XT60 in the iX12, and set the throttle end points the same as they were on the DX8. A small adjustment to the low end and she was set! The idle is still high a touch. Gary suggested a THR<THR Mix set at 5% to a switch. He has it set up on one of his. This would allow me to hit the switch a foot above ground, dropping the idle 5%, which she can sustain for almost a minute before stopping, if she does, allowing power up if needed, or a slower touchdown. We couldn't figure out why it wouldn't work, so I'll be seeing what the folks at Spektrum come up with. Hit about 40 min over three flights!

This 26cc engine is LOUD. The twin exhausts produce a lot of noise. On my RCGF 30cc on the MX-Bach, I have a DLE Muffler Silencer from Mile High RC. It really softens the sound. I measured the external diameter of the pipes at 14.4 mm, and these fit an internal diameter of 14.4 mm, so, we'll see. It really needs some silencing.

I did get to watch Gary fly the crap out of the 6S Edge made with a carbon laminate frame that was so thin a sneeze should break it. I think it was far less than a pound. Man got skillz. It was beautifully built, expertly flown.

I forgot how wet the field can be, as it is on the edge of a wetland. Wet, cold feet... Called it a day. 45 deg, breezy, wet... bad combo. 

Another good day! I really love this sport!

Let's get out there and fly something!

Two cups of coffee, still dragging butt... Planning on heading out to RCAces field in North Hampton, NH, to fly with my buddy, Gary Hoffma, pick up some pointers on landing without ripping the gear off.

First Flights, First Crashes! (No, it wasn't the radio!)

The first flights on my brand new, arrived today, iX12! I actually had already bound and set up the Hangar 9 Pulse XT60 and the Sbach 10cc, but wanted to fly the UMX Pitts S-1S as soon as I could, and have the UMXs to fly in the yard.

This was all me. Flew around a bit then got sun blinded, same as the other day, but this time flew her under my daughter's car. Broken wings.

And with that, I reset the Crash Clock!

Not to be discouraged I flew the UMX into my neighbor's house. The house didn't notice. Broke the front end off and split the battery cover in half. This plane flies fine, but the elevator has had issues.

This was the issue. I've adjusted this a couple of times, hoping each time is the last.

Already have the wings fixed! The top wing was split in half, and came off the plane, the left wing broke off the fuse, and both of the super fragile wing struts broke off. And they broke on installation, just like last time. I used CA hinges to join the broken halves of the upper wing with Beacon 3-in-1, and to join the lower left wing to the fuse. Will be ready to fly as soon as tomorrow.

Epoxied the Timber's nose back on, using a popsicle stick end to support the bottom.

Ready to fly! Letting the epoxy cure. Can be ready as soon as tomorrow.

Up close she has war wounds, but is flight ready!

My iX12 Is In The House!

No, I wasn't looking out the window waiting... Who does that?

COVID-19 Protocol, no touchy!

My wife pulled this off the Blink!

A box of happy!

Comes with a neato hat!

Ah, my precious!

Scha-wing!

Sweet baby Jesus, I love this thing!

New Badness.            Old Badness.

Installed the updates, made a few system preference changes. I likey the English woman's voice set!

First Flight!

Spektrum Tx Box

One of two FedEx deliveries arrived today. Alas, it was just the sweet Transmitter box. The iX12 is supposed to arrive by 8pm tonight, but I don't see that happening. It was in Newark, NJ, at 1pm yesterday but didn't make it today, and they have been here twice already.

Ver nice! I am very glad to have it.

First Flight SNHRCC Hudson, New Hampshire 3/25/2020

Heading out to check out our club field with the Big Stik RCGF 10cc, and the Pulse XT60 RCGF 26cc. First flight at the field for me this season.

SNHRCC is on the city of Hudson's closed trash mountain, I fondly call Mt Hudson. We have to drive thought the city dump. That's it, up there on top of the that hill.

Winds are common here. 

The Electruc side winsock needs replacing.

Hot footing it out! Wonder what they were up  to?

Waaah! The Tx Case arrived, but the Fx hasn't. I expect it tomorrow! 

Waiting to fly...

Pocket RC Flight Sims, Tablet and Phone Flying

Sitting around socially isolating, flying my RF8 and Phoenix RC Flight Sims on the Bat Cave computer, but sometimes I find myself elsewhere. I have a couple of "pocket", or tablet/phone flight sims. There are a lot out there, only two worth really using.

ABSOLUTE FLIGHT SIMULATOR SERIES

By Happy Bytes, LLC

This is simply the best pocket flight sim out there. Steve has done a magnificent job with this product, in terms of functionality, graphics quality, flight simulation realism, and variety of aircraft. He has several, but I have the heli sim and there are planks in there too. The download is free and provides a heli and an airplane to try out, additional aircraft are available for purchase at about $2. 

I think Steve was the maker of Clear View RC flight sim, the very first RC flight sim I ever used.

You can get Absolute at Google Play Store, and the Apple Store, as well as see more on his website.

Start up page, heli.

Planes

Game start screen.

Flight screen start up. The help disappears.

In flight. Look at those graphics!

REAL FLIGHT MOBILE    

By Hobbico (Horizon Hobby)

Also available at Google and Apple.

This is a nicely designed sim, but needs a little tune up. The flight sim is good, the graphics sweet, and it provides airplanes and drones, but no helis. There are 4 fields, the Green Hills RC field being the default that comes with the download which is free and comes with two planes, a Stearman and a NextSTAR trainer, and one field.

4 fields.

Planks and drones.

A $12.95 bundle gives you them all.

The stock Stearman at Green Hills.

Thesexsims are very good, fun, affordable, and easy to use! Get one!